Forum Top Ad MOBILE Smallest

Collapse

Mededeling

Collapse
No announcement yet.

THC en CBD extraheren

Collapse
X
 
  • Filter
  • Tijd
  • Geef Weer
Clear All
new posts

    THC en CBD extraheren

    Korting op 420shop
    Goedemiddag,

    Ik heb een vraagje wat betreft de extractie van THC en CBD: ik zie heel vaak op het internet dat mensen hun wiet pakken, er alcohol bij doen, het vervolgens filteren zodat je een alcohol en thc/cbd mengsel overhoud en dit vervolgens bijvoorbeeld verwarmt zodat de alcohol eruit gaat, alleen waarom moet dit perse met alcohol? Kan dit niet door andere mogelijkheden, een andere vloeistof die wat minder gevaarlijk is bijvoorbeeld? Ik wil het graag extraheren voor medische doeleinden. Ik las ergens dat je ook met olijfolie in een cbd/thc olie kunt bereiden alleen er stond bij dat dit niet echt geschikt was voor bijvoorbeeld tegen kanker, weet iemand waarom?

    Alvast bedankt voor de feedback!

    Met vriendelijke groet,

    C.

    #2
    Re: THC en CBD extraheren

    THC en de andere cabbabedoiden lossen op in plantaardige en dierlijke vetten en in alcoholen. In feite zou je ook slaolie kunnen gebruiken enkel dat verdampt vervolgens niet en dan zou je dus die hele liter slaaolie moeten consumeren om de THC binnen te krijgen. We willen echter een extract, in geconcentreerde vorm voor de medicinale doeleinden. COnsumptie alcohol is een redelijk schoon oplosmiddel wat vervolgens ook weer makkerlijk er uit te dampen is zodat je een concentraat overhoud van het extract. Doorgaans verdunt men dit concentraat wat erg stroperig is en moeilijk is te dozeren 5 of 10 x met een plantaardige olie zodat je het kan optrekken in een spuitje en goed kunt dozeren.
    Als je goed geventileerd uitdampt, buiten, zal je niet ontploffen.

    Verder zijn er nog andere oplosmiddelen die men gebruikt zoals dimitylchloroform van dexso.



    http://www.dexso.com/index.php/produ...anic-degreaser

    Comment


      #3
      Re: THC en CBD extraheren

      Oorspronkelijk geplaatst door FlintStoned View Post
      Verder zijn er nog andere oplosmiddelen die men gebruikt zoals dimitylchloroform van dexso.
      Nog bedankt voor de suggestie Flint, Het Dexso gas en de extractor zijn toegevoegd aan het assortiment
      Veel gestelde vragen over het forum

      JOINTJEDRAAIEN.NL - Smoking Community
      420Shop.NL - Headshop / Seedshop : Korting voor leden van Jointjedraaien.nl

      Comment


        #4
        Re: THC en CBD extraheren

        Dat had ik idd al gezien, nice.

        Nog wat info over dexso

        BHO or DHO
        With the dabbing of BHO quickly gaining popularity, more and more people are making their own BHO or Butane Hash Oil. BHO is a concentrate, made by extraction of cannabis by the use of the liquid pressurized solvent Butane. This butane, sold in aerosol-cans for lighter fuel, is of course flammable, explosive, and neurotoxic when inhaled. The procedure to make this BHO can be dangerously explosive, and without a good purification of the oil, the final product might still contain toxic butane, or impurities from this lighter fuel.

        Since recently there’s an alternative solvent available, which seem to diminish these risks of BHO. The new solvent is D.M.E. or (Dimethyl Ether) and logically the oil which is made with is called DHO. So what are exactly the differences between these solvents?
        Since you probably don’t know much about DME, we will start with this one.

        DME is a biofuel, propellant, and solvent that can be produced in an ecological co2-neutral way from almost any vegetal material. It can easily be used to replace LPG as fuel for cars, and it’s one of the most promising future bio-fuels in research. It is also used as a propellant in aerosol-sprays, for example in mouth sprays for people with asthma. And it has been used for a lot of time as a solvent for all kinds of uses for the food industry. DME is not new, and it is well studied and regulated. It’s low toxicity is generally accepted, as shown by the uses in the food and pharmaceutical industries. It has just never been available in it’s pure form unless you had a solvent or fuel factory. The D.M.E. available nowadays is a real extraction solvent, and known as one of the purest and strongest there is. It’s extraction capacity is stronger than from Butane, resulting in more yield. It is also less explosive, evaporates faster, and leaves practically no residue in your oil.
        Although the oil made with DME can be different than with Butane, it will be normally more oil, with higher concentrations of cannabinoids and terpenes. Also the procedure for the most optimal result might be a bit different than with Butane.

        Butane can consist of normal Butane (or n-Butane) and Iso-Butane. Both are purified out of natural mineral gas, so from natural resources. The source of Butane that is used for extractions, is almost always from Butane meant to be used as a lighter fuel. It is surely not developed or meant to be used as a solvent for oil to consume. But since there was no other solvent available, people got used to Butane.
        Since Butane is an odourless, flammable gas, it is by law required that sulphur is added to give it a recognizable smell, with the purpose of easily noticing dangerous gas leaks. DME has a soft but recognizable smell, so it doesn’t need this additive.


        Why does DME extract more oil than Butane?
        To explain this question we will have to get a bit scientific. The Butane-molecule consists of 2 methyl-groups, which are both capable of making an a-polar connection with lipophilic substances like cannabinoids or terpenes. The DME-molecule has also the 2 methyl-groups, so it can make exactly the same a-polar connections like Butane, but it also has an Oxygen-atom in the middle. This Oxygen-atom can make polar connections which is why DME has an stronger extraction potential than Butane.
        The stronger extraction capacity also shows in another way. DME is capable of dissolving materials, that sare resistant to Butane, like silicone, PVC, or natural rubber. In general, we would advise to avoid any contact with plastic materials except Teflon or Nitrile Butyl Rubber. So take care that your extractor is made of an inert material like glass or stainless steel, and doesn’t have a non-resistant sealing ring. Also during the purging you should avoid any non-resistant tools of course.

        Differences in the extraction procedures of DME and Butane.
        Also the procedure to obtain the best quality is a bit different than with Butane.
        First important step, try to use fresh material. Freshly harvested flowers are perfect to make a terpene and flavourful ‘live resin’ or ‘fresh frozen’ oil, or dried for preferably not more than 2 weeks. The older the material, the less terpenes you can extract, because they evaporate slowly during the drying process. Also, the older your plant material, the darker your oil will be. With fresh plants until max 2 weeks of drying it will normally be possible to make an oil which has a nice, light colour. It does not change much about the cannabinoids you will extract by the way, and a darker oil can be really good, and as rich in cannabinoids than a lighter coloured oil.

        Freeze the extractor filled with flowers and the cans with DME 24 hours before the extraction. This will freeze and block all water in the flowers, and it will also avoid that some undesirable greases will be extracted. The colder the inside of the extractor, the more pure your oil will be. Since the solvent will enter the extractor, it also has to be as cold as possible.

        You can compress the flowers in the extractor, which will offer more yield and more efficiency from your solvent. But if you want the best quality, only compress it minimally, so the solvent runs fast through the extractor, and so will be less time in contact with the flowers.

        You can use a Pyrex bowl to collect the extraction liquid that runs out of the extractor. Even more convenient is it when you put a layer of sulphured baking paper in it, or even better, PTFE-foil like Oil Slick Sheet. This will avoid the need later to scratch the oil from the Pyrex. You can also fold the baking paper or Slick Sheet into the shape of a little box, place this in the Pyrex, and extract directly in the box.

        The extraction liquid will cool off fast, because of the evaporating DME. This will accelerate condensation of water on your liquid and Pyrex. It might even form ice in your Pyrex. You can avoid this by heating the Pyrex by making it float in hot water. This will also accelerate the evaporation of the DME. Try to get the temperature high enough so you have no ice forming in your Pyrex. If ice does form, you will need to be patient to let the ice melt. Also you will have to be patient later during purging, to make sure all water will evaporate from your oil.


        For high-demanding, experienced oil fanatics, there’s also an ‘’ADVANCED’’ method.


        With this method we will extract into warm distilled water. The high temperature (25 degrees) of the distilled water will make the DME evaporate fast, and leave the oil mostly floating on the water. The distilled water has the capacity to extract impurities from your oil through osmotic pressure, and it assures that most DME will evaporate directly.
        For this you will need the box made from Slick Sheet, like mentioned before. The box is placed in a big Pyrex bowl, floating on hot water. The box of Slick Sheet has to be filled with half a litre of distilled water of 30 degrees C.
        The Pyrex will have to float on hot water, way hotter than the distilled water, so it can compensate the cooling caused by the extraction. The extraction will be done directly in the distilled water. Because of the relative hot water, the DME will mostly evaporate directly, leaving the oil on and in the water. Drops of liquid might burst up high, so make sure your box is high enough to apture them all.

        After the extraction we will still see bubbles of DME being released by the liquid. We will have to heat the liquid, so the dissolved DME will be released by the water. As soon as the temperature of the water gets above 20 degrees Celcius again, normally the bubbles will almost be one. Otherwise, we’ll wait a couple of hours more. Now we can scoop most of the oil from the surface of the water and secure it. Then we sting a hole in the box, so the water will run slowly into the Pyrex. The oil will stick to the Slick Sheet.

        Then we dry the oil. Hang the sheet vertically so the water runs off. We use a hair dryer and the corner of a napkin to absorb drops. Then we spread out the oil in a thin layer on the slick sheet, and let it dry more.
        Now we can purge the oil further just like you would (probably) do with Butane, but it is less crucial. DME is not considered to be neurotoxic, and evaporates way faster than Butane. Personally, I leave the oil for 48 hours in a thin layer on the slick sheet, and enjoy my dab afterwards. Every active purge method, like a vacuum oven, or dewaxing in alcohol, will let some terpenes evaporate from your oil.
        Last edited by FlintStoned; 27 October 2015, 12:50.

        Comment


          #5
          Re: THC en CBD extraheren

          Die 15 eurie scheelt alleen nogal met die butaan vd action. .

          Scheelt een berg, proef je niks van..
          Pas u aan aan de onaangepasten. Wees tolerant voor de intoleranten. Omarm hen die u afwijzen. Het systeem heeft gefaald.
          Het systeem betreurt dit ten zeerste.

          Comment


            #6
            Re: THC en CBD extraheren

            Je kan wel 500 gram extraheren me 1 bus. Met butaan heb je daar een bus of 5 voor nodig. Dan kom je dus weer op het zelfde uit.

            Comment


              #7
              Re: THC en CBD extraheren

              Mwa. Voor 15 piek koop ik ongeveer 15 bussen gas dus kom ik op 3 x goedkoper toch?
              Die butaan bussen voor dat gasstelletje zijn nog s 2 x zo groot ook voor paar cent meer dan die gele..

              Waar rook is is BHO..
              Pas u aan aan de onaangepasten. Wees tolerant voor de intoleranten. Omarm hen die u afwijzen. Het systeem heeft gefaald.
              Het systeem betreurt dit ten zeerste.

              Comment


                #8
                Re: THC en CBD extraheren

                Ja zou kunnen. Goedkoop is soms echter duurkoop en omdat het om je gezondheid gaat is de iets goedkopere optie butaan misschien toch niet de slimste oplossing.

                Comment


                  #9
                  Re: THC en CBD extraheren

                  Rood/bewerkt vlees staat sinds gisteren ook qua kankerverwekking naast tabak en alcohol..
                  Lees overigens dat er ether in zit. Dat gebruikten de boeren bij ons om n kattenplaag de kop in te drukken omdat dat hoop goedkoper was dan steriliseren.. Vrij dodelijk roesje zeg ma.

                  Je hebt wel n punt, vind t alleen altijd zo verbazingwekkend dat als iets minder schadelijk voor je is dat het dan ook gelijk zo rete duur moet zijn.

                  Maar soit, elke stap richting BHO is een juiste.
                  Pas u aan aan de onaangepasten. Wees tolerant voor de intoleranten. Omarm hen die u afwijzen. Het systeem heeft gefaald.
                  Het systeem betreurt dit ten zeerste.

                  Comment


                    #10
                    Re: THC en CBD extraheren

                    Kingkong kregen ze er ook mee plat en bij over dozeren idd niet zo handig maar vroeger werd het ook gewoon als verdovingsmiddel bij een operatie. Je gaat niet zozeer dood van de giftigheid maar van het nogal narcotische karakter van de stof bij te hoge concentraties. Ether inademen is minder schadelijk dan even aan je aansteker ruiken.
                    De ether zit er overigens niet in, het is het oplosmiddel zelf in een heel hoge zuiverheid.
                    Verder is he ook de bedoeling dat het oplosmiddel geheel uit het eindproduct is op het einde van het proces. Met niet geheel zuivere butaan blijft er naast eventueel butaan ook deze onzuiverheden achter in het eindproduct. Maar goed nu lijk ik wel een verkoper van dexso. Ik vind het enkel een goed product en een stap de goede richting in. De prijs tja die is idd aan de hoge kant in verhouding met een goedkope bus aanstekergas waarvan je de zuiverheid maar moet gokken. In camping butaan zit vaap een deel propaan om het ook voor de winter geschikt te maken en het een wat hogere varbrandingswaarde te geven (de koffie is dan wat sneller klaar) Maar daarnaast zitten daar ook nog een boel "foezel" bij, Ik zou camping butaan iedereen afraden.
                    Last edited by FlintStoned; 27 October 2015, 13:56.

                    Comment


                      #11
                      Re: THC en CBD extraheren

                      @ Flint, Is er ook een goedkopere optie voor "de buis" van dexso ? Om uit te proberen vind ik het gelijk zo'n grote uitgave.
                      Stemma doet het forum, stout 2017

                      Stemma doet stout (2016)
                      Dark Devil en Punisher#2 in huize Stemma

                      Comment


                        #12
                        Re: THC en CBD extraheren

                        Zelf geven ze hier dus aan dat bijvoorbeeld een honeybee extracter niet geschikt is voor de dexso omdat deze ook harde pvc oplost. Het kan dus enkel in een glazen, roestvrijstale of aluminium extractor.

                        De Dexso dus niet gaan gebruiken met pvc of andere plastics. Ook moet een eventuele dichtingsrubber of oring niet gaan oplossen.

                        Comment


                          #13
                          Re: THC en CBD extraheren

                          Wordt wel hele dure hobby zo Flint..
                          Pas u aan aan de onaangepasten. Wees tolerant voor de intoleranten. Omarm hen die u afwijzen. Het systeem heeft gefaald.
                          Het systeem betreurt dit ten zeerste.

                          Comment


                            #14
                            Re: THC en CBD extraheren

                            Moet mijn Dexso buis nog steeds een keer proberen

                            Dacht er toevallig vandaag nog aan dat het mooi weer was om dat te doen, maar was de hele dag op pad. Hpelijk blijft het nog even mooi weer.

                            Lopen verslag: McPurple S1 Fem van Forum Genetics op DWC met GHE FloraNova onder 400W Cree COBs

                            Comment


                              #15
                              Re: THC en CBD extraheren

                              Oorspronkelijk geplaatst door I love it View Post
                              Wordt wel hele dure hobby zo Flint..
                              ja maar das relatief, blowen kost wel een cent ja en kanker heben ook.
                              Last edited by FlintStoned; 29 October 2015, 07:29.

                              Comment

                              Bezig...
                              X